Strict Standards: Only variables should be passed by reference in /var/www/utchimsteel.ro/public_html/util/db.php on line 188 Utchim Steel - Despre noi

UTCHIM STEEL SRL

Societatea comerciala UTCHIM STEEL SRL este infiintata in anul 2005 si are sediul in Galati, Romania.
UTCHIM STEEL SRL este o firma specializata in comercializarea tevilor de otel. Aceste produse sunt fabricate in Romania, in CE sau provin din import.

Principala activitate o reprezinta comercializarea tevilor de otel sudate pentru constructii de provenienta Mairon Tubes SRL., Romania.

UTCHIM STEEL SRL se adreseaza in principal stockistilor si distribuitorilor de tevi de otel din Romania.

Firma este certificata ISO 9001. Organismul de certificare este CERTIND.
Vendor: Cisco Exam Code: 200-105 Exam Name: Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) Q&As: 310(There are 6 parts in the dump, 310 questions in total. )QUESTION 1 Which command can be used https://www.pass4itsure.com/200-105.html from a router to verify the Layer 3 path to a host? A. tracert address B. traceroute address C. telnet address D. ssh address Correct Answer: B Explanation QUESTION 2 A network administrator has configured access list 173 to prevent Telnet and ICMP traffic from reaching a server with the address of 192.168.13.26. Which commands can the administrator issue to verify that the access list is working properly? (Choose three.) A. Router# ping 192.168.13.26 B. Router# debug access-list 173 C. Router# show open ports 192.168.13.26 D. Router# show access-lists E. Router# show ip interface Correct Answer: ADE Explanation QUESTION 3 Scenario Refer to the topology. Your company has connected the routers R1. R2. and R3 with serial links. R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also connected to the routers R4 and R5. The EIGRP routing protocol is configured. You are required to troubleshoot and resolve the EIGRP issues between the various routers. Use the appropriate show commands to troubleshoot the issues.Which path does traffic take from R1 to R5? A. The traffic goes through R2. B. The traffic goes through R3. C. The traffic is equally load-balanced over R2 and R3. D. The traffic is unequally load-balanced over R2 and R3. Correct Answer: A Explanation Explanation/Reference: Using the "show ip int brief command" on R5 we can see the IP addresses assigned to this router. Then, using the "show ip route" command on R1 we can see that to reach 10.5.5.5 and 10.5.5.55 the preferred path is via Serial 1/3, which we see from the diagram is the link to R2.QUESTION 4 Refer to the exhibit. Assuming that the entire network topology is shown, what is the operational status of the interfaces of R2 as indicated by the command output shown? A. One interface has a problem. B. Two interfaces have problems. C. The interfaces are functioning correctly. D. The operational status of the interfaces cannot be determined from the output shown. Correct Answer: C Explanation Explanation/Reference: R2 has setup with two interface s0/1 and fa0/0 and both are interfaces configured with IP address and up. "show ip interface brief" showing the status of R2 interfaces. QUESTION 5 Scenario Refer to the topology. Your company has connected the routers R1. R2. and R3 with serial links. R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also connected to the routers R4 and R5. The EIGRP routing protocol is configured. You are required to troubleshoot and resolve the EIGRP issues between the various routers. Use the appropriate show commands to troubleshoot the issues.Study the following output taken on R1: R1# Ping 10.5.5.55 source 10.1.1.1 Type escape sequence to abort.Sending 5.100-byte ICMP Echos to 10.5.5.55, timeout is 2 seconds: Packet sent with a source address of 10.1.1.1 Why are the pings failing? A. The network statement is missing on R5. B. The loopback interface is shut down on R5. C. The network statement is missing on R1. D. The IP address that is configured on the Lo1 interface on R5 is incorrect. Correct Answer: C Explanation Explanation/Reference: R5 does not have a route to the 10.1.1.1 network, which is the loopback0 IP address of R1. When looking at the EIGRP configuration on R1, we see that the 10.1.1.1 network statement is missing on R1.
windows8-key  windows-8.1-pro-key  windows-8.1-key  windows-8.1-key-2  windows-8.1-key-3  windows-7-professional